Products

A replacement lower section for our standard Carbon Fiber Trekking Poles.

These will also fit our Minimalist Trekking Poles and most other poles with a 12mm lower section, however the measurement lines may not be accurate on other poles. Mark the spot for your tent height, and for your arm height with a sharpie.

If you are a gram-counter you can saw off the plug, and unneeded length with a hack saw. Just leave a couple inches of overlap.

Don't forget Baskets.

This replacement horizontal flat stay fits our Arc Haul Ultra, Arc Zip Ultra, and discontinued Arc Blast, Arc Zip, Arc Haul, Arc Haul Zip, Arc Scout, Arc Haul Scout, Arc Air and Arc Air Zip Backpacks.

This is a longer version of the standard sternum strap that ships with our backpacks. The webbing is 5" longer and adjusts to a maximum of about 17" (43 cm) from strap to strap.

The sternum strap loops around the daisy chain webbing on our shoulder straps, and should be compatible with other similar shoulder straps.

This is a replacement for the Lycra Back Panel that currently ships with all Arc style backpacks. It creates a trampoline with an air gap against the wearer's back. It is also compatible with all older Arc backpacks as a retrofit.

The Lycra mesh is soft and stretchy and feels good on the wearer's back.

We also have our original style Mesh Back Panels which are made with pocket mesh. Some customers prefer the original style mesh because it is more firm, and has better airflow. Either style are interchangeable on all old or new Arc backpacks.

This is our original style Mesh Back Panel. It is used to add tension to our Arc style backpack frames, and to help maintain a gap for air flow against your back.

This will fit all Arc style backpacks, and can be retrofitted on old or new packs. It is made form our 3.5 oz/sqyd (119 g/m²) pocket mesh. The holes are a little larger than 1/8" (about 4 mm) and they allow very good airflow.

This mesh doesn't stretch as much as the Lycra Back Panels that are currently shipped on all Arc packs. Some customers prefer the more firm pocket mesh, and increased airflow compared to Lycra. Other customers prefer the more soft and stretchy Lycra that is now our default.

These replacement pre-curved vertical stays fit our Arc Haul Ultra, Arc Zip Ultra, and discontinued Arc Air and Arc Air Zip Backpacks.

You may also want to replace your Stay Holster Inserts. Instructions for installing inserts and frame pieces are on the Stay Holster Inserts page.

These replacement pre-curved vertical stays fit our Arc Haul Ultra, Arc Zip Ultra, and discontinued Arc Air and Arc Air Zip Backpacks.

These replacement pre-curved vertical stays fit our Arc Haul Ultra, Arc Zip Ultra, and discontinued Arc Air and Arc Air Zip Backpacks.

You may also want to replace your Stay Holster Inserts. Instructions for installing inserts and frame pieces are on the Stay Holster Inserts page.

These replacement round vertical stays fit our discontinued Arc Blast, Arc Zip, Arc Haul, and Arc Haul Zip Backpacks. If you prefer our original adjustable Arc stay system, these can be retrofitted into any of our new Arc Haul Ultra backpacks. You may need to trim down the length with a hacksaw to get the right fit.

This quilt strap is included with our Solo Quilts and it is an optional add-on with our Summer Quilts.

The strap cinches tight to your sleeping pad. Snap the sides of your quilt to the strap to keep it tucked under you. The snaps can slide along the shock cord to adjust the gap beneath you.

If you have one of our older Solo Quilts with Flat Clips you'll need to purchase the Strap w/ Flat Clips.

Our vertical carbon fiber Arc Frame connects to the backpack by sliding into webbing pockets at the top and bottom of the backpack.

The pockets each contain a "stay holster insert" which covers the ends of stay to help prevent them from punching through the pockets. The inserts have metal sandwiched inside of them making them difficult to wear through.

The inserts are replaceable, and should be checked after 500-1,000 miles, especially if starting a long hike with a used pack.

Instructions:

1. Remove the three horizontal frame bars by pulling from the center until the end pops out. They flex easily and come in and out easily.


2. The vertical stays are difficult to remove. Pull up on the stay pocket, and pull down hard on the stay until the top end slips out of the pocket.


3. If the old inserts did not come out with the stay, slide something skinny (like a tent stake, or a horizontal stay) through the flaps and pull them out.


4. Replace the stay inserts if they are worn or punctured. Make sure the stay is between the two flaps on the inserts and is fully in place at the bottom and top.


5. Put the bottom of the vertical stay in first. Use one of the horizontal stays like a shoe-horn to pry/guide the top back into the upper pocket. It should go in without too much fuss.


6. Flex the three horizontal stays back into place. They should be behind the vertical stays.

This is a replacement for the standard sternum strap that attaches to the daisy chains on our backpack straps.

The sternum strap loops around the daisy chain webbing on our shoulder straps, and should also be compatible with other similar shoulder straps.

The maximum length is about 12" (30.5 cm) from strap to strap and will fit most hikers.

We also have a longer sternum strap available.

These carbon fiber Trekking Pole Lower Sections will fit any clasp-lock trekking poles with a 12mm diameter lower tube, which is common on many brands. They will fit all of our past and current trekking poles. Swapping out the lower section is the easiest way to replace a worn down tip or a broken tube, or simply to drop weight from your older poles.

The measurement lines are marked specifically for our new/current 2026 model Minimalist and Standard Carbon poles. They have English measurements on one side, and metric on the other.

If the measurement lines don't match your older poles, use a sharpie to mark your usual grip height and tent pitch height.

These weigh just 1.1 ounces (31 grams) for the Carbon section, plus .1 ounce (2.8 grams) for the removable basket. Baskets are included.

Keep those trekking poles on trail with our replacement tips. This kit includes the trekking pole tip, basket, and our rubber "road tip."

Featuring a universal threaded pole tip, these pieces fit the majority of standard trekking poles with a ~12mm tapered lower section.

To remove your old tip you will likely need to cut down the side of the tip and pry it off to the break the glue. An alternative, easier solution is to swap out the entire lower section of your pole. Our lower sections will fit any 12mm poles.

These replacement trekking pole clasps are replacements for the clasps found on the upper segment of our Carbon Fiber and Minimalist trekking poles.

This did exactly what it was supposed to. Good quality.

– Jake D., ★★★★★

This webbing is about 1/2" (12 mm) wide and can be used to replace the shoulder strap webbing, load lifters, sternum strap, top strap, or roll top straps on all our backpacks.

Just trim it down to the size you need and singe it with a lighter.

This webbing belt is a replacement for our Front Utility Pack Accessory.

Great, durable rock sack. Don’t waste time trying to tie string around a rock. Perfect for storing cord, too. Keeps bears safe!

– Alex D., ★★★★★

Make bear bagging easy with this rock sack. Just put a small rock, sand, or gravel in it, tie your bear line to it, and toss it over a branch. Constructed from ultralight but durable 1.6 oz/sqyd Dyneema® Composite Fabric to resist abrasion and punctures.

This is also available as part of a Bear Bagging Kit .

Need a different size? Check out the rest of our Stuff Sack collection.

Simple and great to use and helps compact smaller loads.

– Christopher C., ★★★★★

Our detachable Roll Top Closure Straps let you cinch the roll top down to the sides of the backpack, rather than simply clipping it together. If you add these, you still have the ability to secure the top of the pack the normal way by clipping the top to itself.

For long days, long miles this is the filter setup you can trust and forget about. The full size Sawyer Squeeze filter lasts longer and is more reliable than the mini or micro variants.

The 0.1-micron absolute hollow-fiber filter turns questionable sources into reliable hydration, removing 99.99999% of bacteria (like E. coli, salmonella, and cholera), 99.9999% of protozoa (giardia and cryptosporidium), and 100% of microplastics. It’s clean water without the mental math.

It pairs with a 1-liter collapsible TPU bottle that’s BPA-free and FDA-approved, packs down tiny in your side pocket, and stands upright when full, so you’re not wrestling a floppy bag every time you stop to fill up. The Sawyer Squeeze thread pattern is also compatible with standard disposable water bottles like Smart water.

Built for the long haul, the Sawyer Squeeze Filter is reusable and rated up to 100,000 gallons, with thick fiber walls that handle aggressive backflushing to keep your flow rate strong trip after trip. The whole system weighs under 5 ounces and includes a cleaning coupling and plunger so you can keep moving instead of troubleshooting.

Every filter is triple-tested during manufacturing, and every purchase helps support clean water initiatives worldwide—good for your hike, good beyond it.

For long days, long miles this is the filter setup you can trust and forget about. The full size Sawyer Squeeze filter lasts longer and is more reliable than the mini or micro variants.

A 0.1-micron absolute hollow-fiber filter delivers confidence at sketchy sources. The Sawyer Squeeze removes 99.99999% of bacteria (like E. coli, salmonella, cholera), 99.9999% of protozoa (giardia and cryptosporidium), and 100% of microplastics, so you can drink fast and keep moving.

It pairs with a tough, BPA-free, FDA-approved 2L TPU bladder that’s made for trail life, with a wide mouth that makes filling from shallow trickles and seeps way less annoying. The Sawyer Squeeze thread pattern is also compatible with standard disposable water bottles like Smart water.

The reusable Sawyer Squeeze Filter is built for the long haul, rated up to 100,000 gallons, and designed with thick fiber walls that handle rigorous backflushing to keep flow strong trip after trip. At under 6 oz for the system, you get dependable filtration without the weight penalty, plus a cleaning coupling and plunger to keep things running smoothly. Every filter is triple-tested for safety, and it’s versatile enough to run as a classic squeeze system or a gravity setup at camp, whatever fits your pace, your miles, and your routine.

Great item to add to your repair/ditty bag/possibles kit. In a pinch the needle can be converted to a fishing hook. It could also be used for an emergency suture if you don’t have butterfly bandages or superglue to seal a laceration.

– David G., ★★★★★

Be prepared for any mishap and keep your gear in good shape until the end of your thru-hike with this handy sewing repair kit. This kit is perfect for repairing your backpack, clothing, or any other gear items that need a touch up while on trail.

Make sure to order some repair tape for the ultimate field repair kit set up.

The shock cord really helps to compress my pack down while also making it more functional. Great place to hold wet rain gear to dry or hang clothes to dry while hiking. I believe the shock cord is a must have. It adds more versatility and additional storage options.

– Daryl H., ★★★★★

The Shock Cord Lashing add-on can be used to hang items off your pack to dry, or to strap on additional items. The 3/32" shock cord is laced across the front of the backpack over the mesh pocket. The shock cord can be detached when not needed.

Made in the USA.

*This is NOT compatible with our Arc Zip or Arc Haul Zip backpacks.

Keeps your cell phone secure and handy when you need it for navigation or to take a picture. Pouch weighs next to nothing; a must for every serious hiker. I highly recommend this product.

– Paul G., ★★★★★

Shoulder Pouches are the ideal place to keep your small camera or phone in reach for taking quick photos. The main compartment of the shoulder pouches are a good size for your wallet, car keys, map, headlamp, mittens, sunglasses, candy bars, pack towel, GPS, or any other items you would like to have within easy reach. The pouches carry comfortably on your shoulder, and you will hardly notice them there.

The small exterior mesh pocket can be used to store your small items like lip balm, emergency whistle, or a compass.

Designed for the adventurer on the go, our Shoulder Pouch w/ Zipper is the ideal place to store items that you need on the ready, like a small camera, your wallet, a map or your smart phone. The streamlined design carries comfortably on your shoulder, and you will hardly notice them there.

The small exterior mesh pocket can be used to store your small items like lip balm, emergency whistle, or a compass.

These interchangeable, detachable shoulder straps can be attached to all Zpacks backpacks made in late 2024 or later. Just make sure your old straps have clips at the top if retrofitting an existing pack.

These straps include a sternum strap, a pair of tiny oval carabiners to attach them, and a pair of 20" (51 cm) x 1/2" webbing that connects the bottom of the straps to your backpack. Load lifter webbing is also included, and is detachable and not needed with our frameless backpacks.

Vest straps also include a second sternum strap and a second set of 20" (51 cm) x 1/2" webbing w/ D rings which should be looped-on near the corners of your pack.

A small curvy compass with thermometer and cardinal directions. With its small size and precise needle, this is the perfect compass to to bring along your hike.

Not for advanced navigation, but a great aid if you need to find the right direction or a backup for a more advanced compass. It fits right in your pocket or clip it to your backpack's shoulder strap with the included carabiner. The convenient thermometer will keep you aware of your changing environment. Keep this compass with you at all times and stay safe!

A single Duplex Flex replacement pole. This pole has 8 sections and two end tips connected by shock cord tied to each tip. It is marked with white rings on each end.

Tip to Tip Pole Length: 91.25" (232 cm)

Folded length: 12.5" (31.75 cm)

A full set requires FOUR single poles, plus an attachment kit. The full set is found Here.

A single Free Zip 2P replacement pole. This pole has 8 sections and two end tips connected by shock cord tied to each tip. It is marked with blue rings on each end.

Tip to Tip Pole Length: 85.5" (217 cm)

Folded length: 12" (30.5 cm)

A full set requires FOUR single poles.

A single Free Zip 3P replacement pole. This pole has 9 sections and two end tips connected by shock cord tied to each tip. It is marked with red rings on each end.

Tip to Tip Pole Length: 96" (244 cm) 

Folded length: 12" (30.5 cm)

A full set requires FOUR single poles.

This large cotton bag is the perfect at home storage solution for ultralight sleeping bags and quilts! It is breathable and ensures your sleeping bag is not over-compressed. Stuff your bag loosely inside, hang it up in your closet, and you're good to go.

*The bag is not waterproof and is not intended to be used as a pack liner or a storage sack while on trail. Our quilts and sleeping bags include a waterproof dry bag for on trail use.

Imported.

Sleeping Pad Slide Stoppers keep your sleeping pad positioned exactly where you want it on your tent floor. They will prevent your pad from sliding out from under you if you are on a slight incline, or from slipping side to side as you toss and turn. They can also be used to keep a pair of pads snug side by side.

One "Set" includes two straps, each consisting of a pair Stick on Springless Cord Locks and a 26" (66 cm) length of shock cord which will stretch to fit standard or wide sleeping pads. The shock cord can be cinched snug.

The Sleeping Pad Slide Stoppers easily stick to your desire position on your DCF tent floor. For the best results, attach one strap around where you shoulders typically rest on your pad, and the other strap where your hips rest. Slide your pad under both shock cords and then tighten the cords accordingly.

If you are securing two pads side by side with two sets, offset the patches lengthwise so that the pads sit snug beside each other.

The adhesive on these patches sticks well to the Dyneema Composit Fabric tent floors in all Zpacks tents. It may stick OK to polyurethane coated tent floors. The patches can be carefully peeled off if you decide to remove them later.

NOTE: This item is a single strap. Make sure to order at least two straps! Three straps are nice for full length pads.

Used them with my significant other in the [Smokeys] last month and it is so nice to keep the pads from sliding apart and staying cozy. Simple and light design. Would recommend for couples who want to stay close at night.

– Corey S., ★★★★★

Snuggling up next to your partner makes a cold night on the trail better, until your sleeping pads begin to slide apart. Use two or more of these sleeping pad straps to keep a pair of sleeping pads lashed together side by side.